Description

The Hyperlite Circuit boot offers a great fitting and easiest entry adjustable boot. It opens wide and has a true floating tongue for supreme adjustability.

 

The Toe Tension System eliminates heel lift by pulling your heel back into the pocket for a locked-down fit.

 

The fully articulating cuff allows the upper part of the boot to flex with your leg. The new J-bar pads wrap around the ankle bones for a snug fit and eliminate heel lift.

 

Dual quick cinch lace zones and seamless liner construction allow for maximum adjustability and a fit that produces no pressure points, complete with the dual lower velcro closure allowing for easy adjustment and removal of boots in an emergency.

 

Finally, the Hyperlite Team utilizes the new Low Pro plate system for the closest foot to board connection in Hyperlite boot history making it perfect for all-round wake and kiteboarding.

 

Low Pro Plate System:

Dual Density Pro Footbed:

For a comfortable ride and maximum impact protection.

 

Dual Lower Velcro Closure:

For easy adjustment and removal of boots in an emergency.

 

Integrated Heel Brace:

Allows for maximum support and responsiveness.

 

Drop-Through Footbed:
For the closest foot to board connection.

 

Injection EVA Components:
Creating a stylish look and the ultimate weight reduction.

 

All-New Removeable 6 Pro Plate:
Designed to be the strongest possible construction for maximum durability and minimal heel and toe lift.

 

Quick Cinch Lower Lace Zone:

Pull em tight, lock em down and you're ready to shred.

 

Pro-Plate Mounting Locks:

The standard in boot retention. Quicker and easier adjustability, plus maximum angle control for a closer heel or toe side placement.

 

Flow Through Drain Panels and Outsole:

Keep the water out of your boots making them as light as possible.

 

Mounting location:

 

Strata interface:
The System features a Strata specific mounting interface. This can be utilized by using the shorter Phillips head screws and Claw hardware marked “L” and” R”. This mounting location greatly reduces heel and toe lift by putting the anchor point directly under the rider’s foot.

 

Why go to 6" Wakeboard Boot Plates?
6” patterns are now standard on many bindings and boards. 6” binding plates are lighter, stronger and have less torsional flex.

 

* Riders can choose to use both inside and outside mounting locations on Strata track boards. Four additional Strata track t-nuts will be required.

 

You have 6” binding plates and a wake or board with an 8” hole pattern. Are they compatible?
Yes, Liquid Force, CWB and Ronix have binding plate extenders that allow you the full range of stance options.

 

How do I measure my inserts?
Wakeboard Insert Spread refers to the hole pattern on your wakeboard or kiteboard. It is the distance from any hole in the outer group of holes to the corresponding hole in the inner group for each boot mounting area (either Left or Right). Both Hyperlite Strata and Slingshot Fastrack Mounting Systems have infinite stance options.

 

Hyperlite Marek System Boots Sizing:
The Hyperlite System Boots 2011 are built like true footwear so their fit is different from traditional voluminous wake boots. The initial impression of the System boot fit should be more like that of an athletic shoe, snug and supportive. By reducing the internal volume and slop we greatly reduce foot movement inside the boot. This translates into superior board control and response. Because a System boot does not have the internal plastic components preventing it to tighten, a rider does not need to cinch the laces down as tight as a traditional boot. The System Binding also provides the retention so if a rider prefers a little more flexion in the upper zone they can achieve this by loosening the laces in that zone.

The Hyperlite fit is on the smaller side, roughly a ½ size. We encourage customers to try out the next size up that corresponds to their actual foot size and not that of traditional wake boots they have used in the past.

 

Hyperlite Circuit Boot / Shoe Sizes
US	4-8.5	7-10.5	10.13.5
UK	3.5-8	6.5-10	10.13.5
Europe	35.5-42	39-44	44-48.5
CM	23.1-26.7	25.1-27.3	27.3-29.2

* Enter quantity required and click 'Buy Now' Button *

 

Hyperlite Circuit Boot Wake / Kite Bindings - £189.00 Hyperlite Circuit Boots - UK Size 3.5-8: - £189.00 Hyperlite Circuit Boots - UK Size 6.5-10: - £189.00 Hyperlite Circuit Boots - UK Size 10-13.5: - £189.00

Specs

Specifications:

Low Pro Plate System:

Dual Density Pro Footbed:

For a comfortable ride and maximum impact protection.

 

Dual Lower Velcro Closure:

For easy adjustment and removal of boots in an emergency.

 

Integrated Heel Brace:

Allows for maximum support and responsiveness.

 

Drop-Through Footbed:
For the closest foot to board connection.

 

Injection EVA Components:
Creating a stylish look and the ultimate weight reduction.

 

All-New Removeable 6 Pro Plate:
Designed to be the strongest possible construction for maximum durability and minimal heel and toe lift.

 

Pro-Plate Mounting Locks:

Keep the water out of your boots making them as light as possible.

 

Quick Cinch Lower Lace Zone:

Pull em tight, lock em down and you're ready to shred.

 

Flow Through Drain Panels and Outsole:

Keep the water out of your boots making them as light as possible.

Mounting location:

 

Strata interface:
The System features a Strata specific mounting interface. This can be utilized by using the shorter Phillips head screws and Claw hardware marked “L” and” R”. This mounting location greatly reduces heel and toe lift by putting the anchor point directly under the rider’s foot.

 

Why go to 6" Wakeboard Boot Plates?
6” patterns are now standard on many bindings and boards. 6” binding plates are lighter, stronger and have less torsional flex. The System binding can be mounted to a traditional 6” wakeboard insert pattern by using the longer Phillips head screws and larger Claw hardware.

 

This method uses the outermost Claw tracks set at a 6” offset.

 

* Riders can choose to use both inside and outside mounting locations on Strata track boards. Four additional Strata track t-nuts will be required.

 

You have 6” binding plates and a wake or board with an 8” hole pattern. Are they compatible?
Yes, Liquid Force, CWB and Ronix have binding plate extenders that allow you the full range of stance options.

 

How do I measure my inserts?
Wakeboard Insert Spread refers to the hole pattern on your wakeboard or kiteboard. It is the distance from any hole in the outer group of holes to the corresponding hole in the inner group for each boot mounting area (either Left or Right). Both Hyperlite Strata and Slingshot Fastrack Mounting Systems have infinite stance options.

 

 

Reviews

Be the first to review this product and get 10% off >>>>

 

Submit a Product Review for this product >>